Formed plastic rod for pushing the brass contact of a foil wire into the barrel of the point when rewiring.
Formed plastic rod for pushing the brass contacts of an epee wire into the barrel of the point when rewiring.
For holding the wire in Leon Paul style epee blades when re-wiring. These clip on the blade near the forte
Removes dust and grit from point parts without causing corrosion. Please note this is a flammable aerosol product and therefore can not be sent to any destination outside the UK.
Removes rust and dirt from blades and guards to prevent them marking clothing and keep them looking brand new.
Die for cutting or re cutting foil tip threads. This product is for use in conjunction with the die holder reference TD10 below or another similar die holder.
Die for cutting or re cutting epee tip threads. This product is for use in conjunction with the die holder reference TD10 below or another similar die holder.
Die for cutting or re cutting tang threads for all three weapons. This product is for use in conjunction with the die holder reference TD10 below or another similar die holder.
Suitable die holder for TD4, TD6 and TD8 dies.
This multi purpose feeler gauge has a slot for checking epee travel and the size of Sabre blades.
This is the same high quality resin glue that we use for wiring all of our blades. It comes in two bottles and is mixed in a 1:1 ratio. The resin takes around 20 minutes to become touch dry and 8 hours to fully harden. Once dry it is extremely tough while being flexible which means that it lasts much better than
Fast drying re wiring glue for up to 15 blades. Doubles up as a cheap alternative to super glue for all general home use!
1/4" Allan key for all Leon Paul pistol grip crosse nuts.
Allan key for attaching the sleeve of a budget maraging blade.
Wide enough for two Foil or two Sabre blades.
Wide enough for one Epee Blade.
Watchmakers hardened steel screwdriver for use with all manufacturers grub screws.
Screwdriver with wide blade for Epee Inside Guard Sockets.
Tubing for protecting the wires of electric blades when they are being stored un mounted.
Thin red PVC tubing for insulating foil and epee wires between forte and inside guard socket.
Spanner for removing or tightening foil barrels / bases.
Spanner for removing or tightening epee barrels or bases.
Long shanked tommy bar for the 6 mm nuts used in our ultra light carbon fibre handles. This spanner allows you to easily attach the handle using a small nut to a standard cut down crosse tang. If you have the weapon in a vice with the tang pointing upwards a handy tip is to use a small piece of Sellotape to hold the nut in the spanner. This Sellotape will prevent it from falling out when you turn the spanner upside down in order to insert it into the handle.
Foil cloth tape for insulating and protecting the tip end of the blade.
Point tape for insulating and protecting the point and grub screws.
This is a basic test box for checking the functionality of foil and epee points. It checks for the correct resistance, electrical shorts and correct tip function. In conjunction with a test weight it can also be used to check the spring is the correct pressure. You will need a bodywire to use this test box. Runs on two standard AA batteries (not included).
The features for this box are the same as for the TT6 above however it also contains a buzzer for added convenience. The buzzer is particularly useful for checking multiple weapons and for working without looking at the box. Runs on two AA batteries (not included).
This box has similar functionality to the TT6 however, it has a separate pair of LED's that when a fault is detected lock in the on position. You will need a bodywire to use this test box.
This is a more advanced test box with the ability to check both points and body wires. Runs on two AA batteries (not included).
AA batteries for test boxes (pair)
Armourers weapon control board for checking flexibility, size guard size etc... Please note this is a special order item and will take approximately 28 days to ship. For more details on this product please call 404 653 9933
Weight for testing foil points.
Weight for testing epee points.
Combi weight for testing both foil and epee points.
Weight for testing lame resistance. This is a test probe for measuring the conductivity of lame jackets when connected to an ohmmeter. To test the jacket you place one probe of the ohmmeter on the lame and then attach the weight to the other side probe of the ohmmeter. You then rest the probe on the lame and move it around to check that the resistance conforms to regulations.
Masks must have an angle of less than 130 degrees. Masks that have a flatter profile on the front are dangerous as blades can catch on the front of the mask mesh instead of being deflected to the sides. This is a handy device for measuring the front angle to ensure the mask is legal.
